Level 1
The Level 1 sub is "Bass on a Budget".
When we sat down to design this driver we were looking at making an in-expensive sub with great SQ and lots of output. Because there are a lot of entry level subs out there, we wanted to make sure that anyone who buys a DC Level 1 get everything and more in comparison to how much came out of pocket for it. I think we did just that.
Level 2
This
is one of our greatest accomplishments. It’s a sub that has everything you need
in a daily driver except the cost.
The Level 2 starts out with a double-stacked FEA optimized motor wrapped in a magnet boot with a chrome top plate and T yoke to keep it looking good.
It has 18 mm of X-Max, progressive spider, 2.5" voice coil, cast basket, push terminals
and a under rated suggestion of 300w RMS/600w peak power handling.
This sub works great in sealed or ported enclosures and defiantly gives you more bang
for your buck!
Key Features
• Extremely rigid non-pressed paper cone assembly
• Multilayered polymer foam surround
• Polypropylene dust cover with embossed DC logo
• 8” OD flat linear roll spider
• Heavy duty interweaved tinsel lead wire
• Cast aluminum black frame
• FEA analyzed and optimized motor assembly - Fully CNC machined
• Rubber mounting gasket
• Chrome spring loaded push terminals
• Dual 4 ohm 2.5” Hi-temp Aluminum voice coil wound on black
anodized voice coil former
• Rubber magnet cover
Level 3
The level 3 sub is the ultimate daily driver sub.
It puts out the low lows and lots of output designed for sealed or ported enclosures.
The Level 3 sub is a triple stacked FEA optimized motor wrapped in a magnet boot
with a chrome top plate and T yoke, the deep gap offers more X-max for 22.5mm.
This sub also comes with a upgraded progressive spider, cone, surround, 3" voice coil, cast basket, push terminals, and upgraded lead wire.
We give the Level 3 a power rating of 600w RMS/1200w peak and is probably our #1 seller.
Key Features
• Extremely rigid non-pressed paper cone assembly
• Multilayered polymer foam surround
• Polypropylene dust cover with embossed DC logo
• 8” OD semi cup progressive roll spider
• Extra heavy duty interweaved tinsel lead wire
• Cast aluminum black frame
• FEA analyzed and optimized motor assembly – Fully CNC machined
• Rubber mounting gasket
• Chrome spring loaded push terminals
• Dual 4 ohm 3” Hi-temp Aluminum voice coil wound on black anodized voice coil former
• Rubber magnet cover
Level 4
This
sub was designed to make people angry.
With sick amounts of output, it’s hard to beat!
The Level 4 sub is a large double stacked motor weighing in at almost 30LBS each, wrapped in a magnet boot with a chrome top plate and T yoke yielding 23.5mm of X-Max
You also get with the upgraded progressive spiders, cone, surround, 3" coil, cast basket, push terminals and upgraded lead wire.
The Level 4 is rated at 1000w RMS and 2000w peak. Designed for ported enclosures and is a great choice for high-powered daily systems and competitors.Key Features
• Extremely rigid non-pressed paper cone assembly
• Multilayered polymer foam surround
• Polypropylene dust cover with embossed DC logo
• 8”OD semi cup progressive roll spider
• Extra heavy duty interweaved tinsel lead wire
• Cast aluminum black frame
• FEA analyzed and optimized motor assembly – Fully CNC machined
• Rubber mounting gasket
• Chrome spring loaded push terminals
• Dual 2 ohm 3” Hi-temp Aluminum voice coil wound on black anodized voice coil former
• Rubber magnet cover
XL
This sub was developed out of demand.
We were getting a lot of requests for something bigger than the LV4 but doesn't kill the gas mileage like the LV5 80+ lbs subs. We were moving a lot of hybrid subs that used LV4 motors with LV5 coils but we knew we could do better than that.
So we thought, everyone likes the LV5, It’s a fantastic sub... Lets use it as the platform for an in-between sub. We played around with a smaller version of the LV5 - That’s exactly what the XL is... It uses all of the same soft parts of the LV5 with a smaller version of the same motor. Just small enough to squeeze through the cut-out hole for a 10" driver. What was the end result? A great sounding high powered daily driver sub that can be used in or out of the competitive lanes. The XL has devastating lows and reliability. It quickly became our best selling sub!
Key Features
• Extremely rigid non-pressed paper cone assembly
• Multilayered polymer foam surround
• Polypropylene dust cover with embossed DC logo
• 8”OD semi cup progressive roll spiders
• Extra heavy duty interweaved tinsel lead wire
• Cast aluminum black frame
• FEA analyzed and optimized motor assembly – Fully CNC machined
• Rubber mounting gasket
• Chrome spring loaded push terminals
• Dual 1ohm , 1.4 or 2 ohm 3” 8 Layer Hi-temp Aluminum voice coil wound on black anodized voice coil former
Level 5 – “Carnage”
A lot went into the design of this sub. We wanted an SPL sub without the drawbacks that some of the others encounter.
We had an idea, it was a sub with sick amounts of magnetic force but with a large gap
and cooling. This is something you don't see from other companies. But why would we be different? The answer is less coil failures and less re-cones. The only drawback (if it is one) you need a 73lbs motor to get the job done. Was it worth it? Yes it was!
The end result is a sub that has extreme amounts of output for the SPL lanes but reliable enough for a high-powered daily system.
When it was all done we ended up with a 73lbs triple stacked 1" slug, FEA optimized monster. We use a 8-layer flat wound 3" coil. Its available is D1ohm or D2ohm configurations. We also use upgraded multiple progressive spiders, upgraded cones, surround, lead wire, a cast basket and push terminals.
Key Features
• Extremely rigid non-pressed paper cone assembly
• Multilayered polymer foam surround
• Polypropylene dust cover with embossed DC logo
• 8”OD semi cup progressive roll spiders
• Extra heavy duty interweaved tinsel lead wire
• Cast aluminum black frame
• FEA analyzed and optimized motor assembly – Fully CNC machined
• Rubber mounting gasket
• Chrome spring loaded push terminals
• Dual 1ohm or 2 ohm 3” 8 Layer Hi-temp Aluminum voice coil wound on black anodized voice coil former
